Beskrivelse

Få betalt for arbeidet du utfører:
Med NetXpert kan du generere oversiktlige PDF rapporter og legge ved som faktureringsgrunnlag!!

Leveringstid: 4-5 arb.dager.

Vi tilbyr leasingavtale via DNB, be om tilbud.

 

Testing av fiber krever en ekstra hovedenhet/main unit.
Se type «NetXpert XG PLUS Fiber testing»
Obs! SFP moduler må kjøpes separat.

 

Varianter

I variantene «NetXpert – up to x Gbit/s», sendes det en «main unit» og en «remote unit» med lisens som støtter opp til 1 Gbit/s.
Ved kjøp av varianter som kan måle høyere hastigheter, følger det med lisensoppgraderinger.
Dette vil si at det er mulig å kjøpe en enhet som støtter 1 Gbit/s og senere kjøpe lisensoppgraderinger slik at det er mulig å måle høyere hastigheter.
For å teste fiber kreves det to hovedenheter (se pakken «NetXpert XG PLUS Fiber testing»).
Det er også mulig å kjøpe ekstra remote unit separat.

Se nederst for nøyere beskrivelse av vareinnhold.

 

The new generation of Ethernet Speed Certification

• From 100Mb/s to 10 Gb/s
• Copper and fiber testing
• Performs 3 tests in one (SNR, BERT and Delay Skew)

 

Technical features at a glance

• Tests data cabling for IEEE 802.3 compliance at data rates
  of up to 10 Gb/s (BERT)
• Determines signal-to-noise ratio (SNR)
• Measures delay skew
• Combined length measurement performing TDR and capacitance measurements for highly accurate test results and easier troubleshooting even of shorts
• Full-color wire map shows opens, shorts, miswires, and split pairs in a clear and easy to understand way
• Saves test results and generates standards-based measurement reports providing „Pass/Fail“

 

Network and diagnosis

• Supports IPv4 and IPv6
• Discover your network and see the connected network devices
• Identifies defective PoE switches with a PoE load test
• DHCP test
• Ping lists can be defined and saved for later use
• LLDP/CDP detection and analysis
• Identifies VLANs present in your network
• Data transfer from the tester to the PC using USB stick

 

 

Test for highest network speeds with your qualifier

The new NetXpert XG verifies, if cabling channels support maximum transmission rates of up to 10Gb/s, irrespective of the category of cables, patch panels, or outlets installed. NetXpert XG provides a precise statement by automatically performing three individual tests which are combined into an overall test result.

New standards defining data rates up to 10Gb/s are a big challenge for the qualifiers of the latest generation. Particularly cabling for wireless access points has to support the ever increasing data rates. In order to verify if the cabling installed is able to support the increased data rates, operators need to perform adequate testing before commissioning the network, to avoid any unpleasant surprises. NetXpert XG enables you to meet the new challenges now!

 

Bit Error Rate test, Signal-to-noise ratio and Delay Skew

By performing a Bit Error Rate Test (BERT) and standardsbased tests as per IEEE 802.3an the NetXpert XG verifies the error-free data transmission up to 10Gb/s. The tests include further parameters that can impact a Gigabit transmission, such as signal-to-noise ratio (SNR) and delay skew. Delay skew indicates the signal time delay between the wire pairs used. Excessive delay can result in a serious degradation of transmission performance, making it impossible for the receiver to interpret the data stream correctly. Delay skew, just as the signal-to-noise ratio, are considered to be crucial parameters for a reliable data transmission.

 

User-friendly operation

Continuity test results of all 8 wires and the shielding are displayed in wire map format in full color, while showing cable faults such as opens, shorts, miswires, and split pairs in a clear and easy to understand way. NetXpert determines the cable length and the distance to faults performing full TDR (Time Domain Reflectometer) measurement in combination with a capacitance measurement, for increased accuracy.

Getting results faster

An autotest can be initiated either from the main unit or from the Active Remote, saving time spent for walking between outlets and reducing the overall working time.When troubleshooting, all cable tests can be performed individually, to minimize fault-finding time.

 

High-resolution 7-inch touch screen

The large high-resolution touch screen display facilitates work
not only in daylight but also in poor lighting conditions, while
the 7″ touch screen provides sufficient space to ensure excellent
readability of the displayed test results.

Ruggedized casing with hanging straps

Equipped with hanging straps at both sides, the NetXpert XG allows for one-handed use, leaving the right/left hand free to connect the NetXpert XG to the next cabling channel under test.

 

Troubleshooting of active PoE++ networks

For the troubleshooting of active PoE++ networks, NetXpert XG additionally offers a comprehensive tool set. This includes load tests for voltage drop to verify stability of PoE supplies, identification of the devices connected to the network, and detection of availability of priority devices. NetXpert XG offers sufficient internal storage even for large projects and, if required, generates complete standardsbased measurement reports containing all the necessary test information. Extensive accessories turn the NetXpert XG into the ultimate multitool – from locating individual cables with the builtin tone generator or the Remote Identifiers, to generating measurement documentation and in-service troubleshooting of PoE++ networks.

 

Including ports for fiber optic measurements

The NetXpert offers full flexibility regardless of whether you are measuring fiber or copper cabling. Using the available SFP/SFP+ ports, various active fiber tests such as protocol detection (CDP/LLDP), network ping test and network discovery can be performed. In the area of passive tests, a throughput test of the fiber optic cabling is also possible.

 

Well-equipped for the challenges of the future

NetXpert XG ensures a future-proof start into the new era of high-speed qualification. The NetXpert series offers simple firmware upgrades, and a license system allows for later upgrades to add new features. There are 3 options (NetXpert 1G, NetXpert 2.5/5G and NetXpert XG). The purchase of an upgrade license always extends the functionality of the device one step upwards. All wear parts (e.g. RJ45 jack) can easily and conveniently be replaced.

 

 

Innhold:

NetXpert XG up to – «1 Gbit/s», «2,5 and 5 Gbit/s» og «10 Gbit/s»

Inneholder:
1 x NetXpert main unit
1 x NetXpert remote unit for kobber
2 x Power supplies
2 x RJ45 Kat 6A patchekabler
Manual
USB adapter
Bæreveske

 

NetXpert XG License upgrade
Inneholder:
Lisensoppgradering, ett hakk.
F.eks: fra «1 Gbit/s» opp til «2,5 og 5Gbit/s»

 

NetXpert XG Plus Fiber testing
Inneholder:

2 x NetXpert Main units
1 x NetXpert remote unit for kobber
3 x Power supplies
2 x RJ45 Kat 6A patchkabler
2 x OM4 LC Duplex Multimode patchkabler
2 x OS2 LC Duplex Singlemode patchkabler
Copper and fiber couplers
Manual
Bæreveske
USB adapter

 

NetXpert XG 10G Fiber Extension kit
Inneholder:

1 x NetXpert main unit
1 x Power supply
2 x multimodus og singelmodus LC duplex kabler
2 LC duplex couplers
Bæreveske
Quick reference guide

 

NetXpert XG Remote unit
Inneholder:

1 x NetXpert remote unit
1 x Power supply
1 x RJ45 Patchkabel